Hi,欢迎访问北京北广精仪仪器设备有限公司

北京北广精仪仪器设备有限公司

摩擦磨损量试验机宁海

联系我们
  • 北京北广精仪仪器设备有限公司
  • 陈丹
联系方式
北京北广精仪仪器设备有限公司
  • 联 系 人:陈丹
  • 手 机 号:
  • 公司电话:
  • 公司地址:北京
文章详情

摩擦磨损量试验机宁海

发布用户:Bgjy 时间:2021-10-27 07:34

摩擦磨损量试验机宁海

摩擦磨损量试验机宁海


产品名称:塑料滑动摩擦磨损试验机

型号:M-200 特点:本机采用高精度扭矩传感器,嵌入式中央单元处理系统cpu控制,支持xp  win7. win8.  win10系统,软件实时绘制显示扭矩-时间曲线、摩擦系数-时间曲线,绘制摩擦力、摩擦系数、磨损量等曲线变化,可设定试验次数,显示当前试验次数,设定时间及当前试验时间等多种功能;

本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度;

配有彩色打印机,可以打印出带有曲线,表格数据,试验单位名称等精美的试验报告单。另外本仪器配有故障自动报警系统问题报警灯和软件报警灯同时提示出现问题时间保护仪器以免零件损坏。是各个科研单位,大学,企业实验室的必备检测设备。

摩擦磨损量试验机宁海

试验负荷;E. test load;

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

负 荷: 196N ± 0.2%(可扩充到392N)

加载系统,对试样和圆环,可施加法向力,精确到5%以内。Loading system, for the sample and the ring, the additional force can be applied, accurate to within 5%.

具有试验人员分级管理功能。It has the function of grading management of the testers.

产品装箱单一份。A single copy of the packing of the products

转动速度: 0-200转/分 连续可调到500转/分

注:圆环材质也可按产品标准另定。Note: the ring material can also be determined according to the product standard.

试验负荷;E. test load;

精度:速度精度≤1%;负荷精度≤0.5%;摩擦力矩精度≤1%;计数器精度≤1S;传感器测量精度≤1accuracy: speed accuracy is less than 1%; load accuracy is less than 0.5%; friction torque accuracy is less than 1%; counter accuracy is less than 1S; sensor measurement accuracy is less than 1%F.

摩擦磨损量试验机宁海

试样尺寸: 30mm*7mm*6mm±0.1 mm

试样夹具结构和尺寸见图并附配垫圈 4 GB 848-沉头螺钉M3×0.35长10毫米。要保证试样安置后无轴向窜动。See Fig. 2 for the structure and dimension of the sample clamp, with washer 4 GB 848- countersunk screw m3 × 0.35 with length of 10 mm. Ensure that there is no axial movement after the sample is placed.

产品使用说明书一份

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

产品装箱单一份

转动速度rotation speed: ≤200 转/分(可调adjustable);

砝码重量:4KG砝码一件,1KG砝码4件,可实现重量叠加功能。

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

采用高精度电机、驱动机、传感器,精度高。using high pcision motor, drive and sensor, high accuracy.

停止:停止试验,试验结束。打印:打印试验报告。

摩擦磨损量试验机宁海

主要适用范围适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦,摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。

精度:速度精度≤1%;负荷精度≤0.5%;摩擦力矩精度≤1%;计数器精度≤1S;传感器测量精度≤1accuracy: speed accuracy is less than 1%; load accuracy is less than 0.5%; friction torque accuracy is less than 1%; counter accuracy is less than 1S; sensor measurement accuracy is less than 1%F.

主要配置:

转动速度rotation speed: ≤200 转/分(可调adjustable);

环境温度、温度及状态调节条件;C. environment temperature, temperature and state regulation conditions;

计算机控制系统一套;A set of computer control systems;

负荷精度:0.5%

产品装箱单一份。A single copy of the packing of the products

产品装箱单一份

注:试验设备本标准推荐采用M-200型磨损试验机。Note: M-200 wear testing machine is recommended in this standard.

摩擦磨损量试验机宁海

特点:Characteristic:

产品合格证一份;A copy of the product certificate;

计数器精度:1S

9退出功能: 退出系统。

供电电源 (鸿海)

转动速度rotation speed: ≤200 转/分(可调adjustable);

具有试验人员分级管理功能。It has the function of grading management of the testers.

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

采用高精度电机、驱动机、传感器,精度高。using high pcision motor, drive and sensor, high accuracy.

复合材料滑动摩擦磨损试验机  技术参数Technical parameters:  M-200

摩擦磨损量试验机宁海

计 数 器: 0-9999小时

复合材料滑动摩擦磨损试验机   本机采用高精度扭矩传感器,16 位单片机电子处理系统,使得本仪器各项测试指标精度非常高。由于集成程度很高,所以设备本身的稳定性极好,本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度,同时通过打印机打印试验数据等功能。是各个科研单位,大学,企业实验室的必备检测设备。

结构紧凑,使用方便,简单。The structure is compact, easy to use and simple.

试样夹具结构和尺寸见图并附配垫圈 4 GB 848-沉头螺钉M3×0.35长10毫米。要保证试样安置后无轴向窜动。See Fig. 2 for the structure and dimension of the sample clamp, with washer 4 GB 848- countersunk screw m3 × 0.35 with length of 10 mm. Ensure that there is no axial movement after the sample is placed.

主要适用范围适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦,摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。

控制线:一头接设备,一头接电脑上边串口复合材料滑动摩擦磨损试验机 本仪器融合了当前 的智能电路系统进行控制,并结合老式M-200摩擦磨损试验机的功能进行改造而成,本仪器具有测控精度高,操作便捷等优势,是科研院所、质检机构、实验室研究的试验设备。

产品合格证

加载系统,对试样和圆环,可施加法向力,精确到5%以内。Loading system, for the sample and the ring, the additional force can be applied, accurate to within 5%.

主要配置:

复合材料滑动摩擦磨损试验机   本机采用高精度扭矩传感器,16 位单片机电子处理系统,使得本仪器各项测试指标精度非常高。由于集成程度很高,所以设备本身的稳定性极好,本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度,同时通过打印机打印试验数据等功能。是各个科研单位,大学,企业实验室的必备检测设备。

摩擦磨损量试验机宁海

塑料名称、规格、牌号、生产厂;A. plastic name, specification, brand and manufacturer;

打开:可以打开以前保存的文件,重新获得数据,打印报告。

具有试验人员分级管理功能。It has the function of grading management of the testers.

计算机数据采集卡一块;A piece of computer data acquisition card;

电脑一套(联想,双核cpu、2g内存、250g硬盘、2.3主频 19显示屏 win7系统)

保存:完成试验后可保存试验数据。

试验报告Test report

配件parts:

产品合格证

记录圆环转数的计数器或记时器,精确到1%以内。A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

环境温度、温度及状态调节条件;C. environment temperature, temperature and state regulation conditions;

高精度扭矩传感器一只;High pcision torque sensor one;

摩擦磨损量试验机宁海

主要配置:

试验主机一台;Test host one;

主要技术指标:

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

主要适用范围适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦,摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。

接线说明

产品装箱单一份

注:试验设备本标准推荐采用M-200型磨损试验机。Note: M-200 wear testing machine is recommended in this standard.

试验报告Test report

标准摩擦环二件;Two standard friction rings;

摩擦磨损量试验机宁海